M22 P WBE HPA Manual Airspray Spray Gun Pressure
- Low to high viscosity material
- Polyurethane needle & treated metal nozzle: reduce the wear caused by abrasive products
- Light and easy to handle, especially when used with our new hoses
|Designation||Value||Unit: metric (US)|
|Maximum Fluid Pressure||6 (87)||bar (psi)|
|Maximum Fluid Outlet||400 (14)||cc/min (oz/min)|
|Minimum Fluid Outlet||200 (7)||cc/min (oz/min)|
|Maximum Air Pressure||6 (87)||bar (psi)|
|Recommended Air Pressure (min)||3 (43.5)||bar (psi)|
|Air Consumption||17.5 - 36.1 (10.3 - 21.2)||m3/h (cfm)|
|Maximum Fluid Temperature||50 (122)||°C (°F)|
|Air Inlet||M 1/4" NPS|
|Fluid Inlet||M 3/8" NPS|
|Wetted parts: Treated Stainless Steel, Stainless Steel, PU||♦|
|Weight||520 (18.3)||g (oz)|
|Tips / Nozzle||♦|
|Designation||Max Fluid viscosity (CA 4)||Projector||Nozzle size||Air Consumption||Fluid Output||Fan width at 20cm (8in)||Part number|
|M22 P WBE||< 20 s||07 EN 3||0.7 mm (0.028 in)||28 m3/h (16.5 cfm)||200 cc/mn (6.8 oz/mn)||27.5 cm (10.6 in)||135148201|
|M22 P WBE||< 20 s||09 EN 3||0.9 mm (0.035 in)||30 m3/h (17.6 cfm)||250 cc/mn (8.5 oz/mn)||31 cm (12.2 in)||135148202|
|M22 P WBE||20 - 40 s||12 EN 3||1.2 mm (0.047 in)||32.5 m3/h (19.1 cfm)||300 cc/mn (10.1 oz/mn)||35 cm (13.8 in)||135148203|
|M22 P WBE||20 - 40 s||15 EN 3||1.5 mm (0.059 in)||34 m3/h (20 cfm)||350 cc/mn (11.8 oz/mn)||36 cm (14.2 in)||135148206|
|M22 P WBE||20 - 40 s||18 EN 3||1.8 mm (0.071 in)||36.1 m3/h (21.2 cfm)||400 cc/mn (13.5 oz/mn)||39 cm (15.4 in)||135148207|
|M22 P WBE||> 40 s||23 EN 3||2.3 mm (0.091 in)||17.5 m3/h (10.3 cfm)||400 cc/mn (13.5 oz/mn)||36 cm (14.2 in)||135148208|
|Designation||Max Fluid viscosity (CA 4)||Aircap||Nozzle size||Needle||Compatibility||Air Consumption||Fluid Output||Fan width at 20cm (8in)||Part number|
|PROJECTOR||< 20 s||EN 3||0.7 mm (0.028 in)||07 - 23||-||28 m3/h (16.5 cfm)||200 cc/mn (6.8 oz/mn)||27.5 cm (10.6 in)||1||031148001|
|PROJECTOR||< 20 s||EN 3||0.9 mm (0.035 in)||07 - 23||-||30 m3/h (17.6 cfm)||250 cc/mn (8.5 oz/mn)||31 cm (12.2 in)||2||031148002|
|PROJECTOR||20 - 40 s||EN 3||1.2 mm (0.047 in)||07 - 23||-||32.5 m3/h (19.1 cfm)||300 cc/mn (10.1 oz/mn)||35 cm (13.8 in)||3||031148003|
|PROJECTOR||20 - 40 s||EN 3||1.5 mm (0.059 in)||07 - 23||-||34 m3/h (20 cfm)||350 cc/mn (11.8 oz/mn)||36 cm (14.2 in)||4||031148006|
|PROJECTOR||20 - 40 s||EN 3||1.8 mm (0.071 in)||07 - 23||-||36.1 m3/h (21.2 cfm)||400 cc/mn (13.5 oz/mn)||39 cm (15.4 in)||5||031148007|
|PROJECTOR||> 40 s||ER 3||2.3 mm (0.091 in)||07 - 23||-||17.5 m3/h (10.3 cfm)||400 cc/mn (13.5 oz/mn)||36 cm (14.2 in)||6||031148008|
|NEEDLE||-||-||-||07 - 23||nozzle 0.7 to 2.3||-||-||-||9||033148100|
|NOZZLE||< 20 s||-||0.7 mm (0.028 in)||-||aircap EN 3||-||-||-||90||134135100|
|NOZZLE||< 20 s||-||0.9 mm (0.035 in)||-||aircap EN 3||-||-||-||91||134135200|
|NOZZLE||20 - 40 s||-||1.2 mm (0.047 in)||-||aircap EN 3||-||-||-||92||134135300|
|NOZZLE||20 - 40 s||-||1.5 mm (0.059 in)||-||aircap EN 3||-||-||-||93||134135600|
|NOZZLE||20 - 40 s||-||1.8 mm (0.071 in)||-||aircap EN 3||-||-||-||94||134135700|
|NOZZLE||> 40 s||-||2.3 mm (0.091 in)||-||aircap ER 3||-||-||-||95||134136100|
|SS EXTENSION D.8 LG250 LATERAL FAN TIP 12 FOR M22 GUN||Lateral extension 250mm length - Ø 8mm - nozzle 12||1||075900111|
|SS EXTENSION D.8 LG 250 LATERAL FAN TIP||Lateral extension 250mm length - Ø 8mm - nozzle 18||2||075900122|
|SS EXTENSION D8 LG150 ROUND FAN TIP 12 FOR M22 GUN||Cone extension 150mm length - Ø 8mm - nozzle 12||3||075900213|
|SS EXTENSION D8 LG150 ROUND FAN TIP 18 FOR M22||Cone extension 150mm length - Ø 8mm - nozzle 18||4||075900224|
|SS EXTENSION D8 LG400 LATERAL FAN TIP 12 FOR M22 GUN||Lateral extension 400mm length - Ø 8mm - nozzle 12||5||075900311|
|SS EXTENSION D8 LG400 JET LATERAL BUSE 18 PR PIST. M22||Lateral extension 400mm length - Ø 8mm - nozzle 18||6||075900322|
|PACK OF SEALS FOR M22G AND M22P||Pack of seals||7||129130901|
|SERVICING KIT FOR M22P||Maintenance pack (includes a pack of seals + gun components)||8||129140902|
|NEEDLE-END FOR NOZZLE TYPE 7 TO 27 (PACK OF10)||Pack of 10 PU needle end for nozzle 0.7 to 2.7||92||129417005|
Epoxy primer/sealer is a non-porous finish that is typically recommended as the first base coat over bare steel.
Epoxy primer/sealer multi-component is a non-porous finish base mixed with a hardener that is typically recommended as the first base coat over bare steel.
Designed to hide profile & surface imperfections, multi-component polyurethane primers & sealers improve adhesion of top coats to the substrate due to the addition of a hardener.
Designed to hide profile & surface imperfections, water-based primers & sealers are environmentally friendly.
Designed to hide profile & surface imperfections, polyurethane primers & sealers promote adhesion of top coats to the substrate.
The Anti-Corrosion Epoxy Multi-Component product is highly resistant to marine & industrial environments, buried conditions, ground water, effluents, salt water & a wide range of oils & chemicals.
Zinc coatings when applied to blasted steel provide excellent anti-rust spray coating corrosion protection, weathering protection & very good resistance to salt water & solvents. Inorganic zinc coatings provide excellent anti-rust corrosion protection when used in chemical plants, refineries & coastal or offshore installations. This coating can provide even better corrosion protection when a top coat is applied. Inorganic zinc coatings are compatible with epoxies, phenolics, acrylics, silicones & many other coatings.
A two-component efficient coating product, used as first layer on metallic surfaces & in a wide range of painting systems. Forms an excellent quality anti-corrosive polyurethane film, ensuring the adherence between the surface & the next layer of the painting process.
Anti-Corrosion Epoxy is applied for active anti-corrosive & anti-rust protection of iron & steel surfaces that are to be coated. It is extremely hard & resistant to friction. It is particularly resistant to diluted acids, alkalis, petroleum products, some solvents, water, sea water, and more.
Used for the steel structures of steel pipeline, steel frame, bridge & plant facilities for effective, long-term substrate protection.
Anti-fouling paint, or bottom paint, is a specialized coating applied to the hull of a ship or boat to slow the growth of sub-aquatic organisms that attach to the hull & can affect a vessel's performance & durability.
Enamel paint air dries to a hard, typically glossy finish, and is used for coating surfaces that are outdoors or otherwise subject to hard wear or temperature changes.
A wood stain consists of a colorant suspended or dissolved in an agent or solvent. Colored, or ''stained", finishes do not penetrate the pores of the wood to any significant degree.
Chemical Agent Resistant Coating (CARC) is available in a water-based solution for environmental protection.
Chemical Agent Resistant Coating (CARC) is a paint commonly applied to military vehicles to provide protection against chemical & biological weapons. The surface of the paint is engineered to be easily decontaminated after exposure to chemical warfare & biological warfare agents. The paint is also resistant to damage & removal by decontaminating solutions.
Chemical Agent Resistant Coating (CARC) can be two-component polyurethane paint commonly applied to military vehicles to provide protection against chemical & biological weapons.
Catalyzed polyurethane clear coats and paints are prized for their durability and versatility around the world. They are used on everything from wood cabinetry, mill work and furniture to planes, trains, and automobiles. They are usually mixed with isocyanates in the hardener. The isocyanate component of polyurethane reacts with moisture in the air and form a hard crystalline structure.
UV-resistant epoxy systems mixed with hardener cure faster & in moist conditions.
UV curable epoxy systems do not require the addition of curing agents. They cure within minutes, or even seconds, and have unlimited working times.
Polyurethane Top Coat is a two- or three-pack isocyanate-cured polyurethane that gives a durable, high gloss finish. Isocyanates included in the hardener are moisture-sensitive & need a specific process for insulating the circuit.
Two-part epoxy coatings were developed for heavy duty service on metal substrates & use less energy than heat-cured.
The newest metallic epoxy system on the market allows contractors to heighten the effects & make floors look three-dimensional.