M22 P Basik HPA Manual Airspray Spray Gun Pressure
- Low to medium viscosity material
- Easy to handle gun, especially when used with our new hoses
- Good finish quality
|Designation||Value||Unit: metric (US)|
|Maximum Fluid Pressure||6 (87)||bar (psi)|
|Maximum Fluid Outlet||400 (14)||cc/min (oz/min)|
|Minimum Fluid Outlet||250 (8.8)||cc/min (oz/min)|
|Maximum Air Pressure||6 (87)||bar (psi)|
|Recommended Air Pressure (min)||2.9 (42)||bar (psi)|
|Air Consumption||31 (18.2)||m3/h (cfm)|
|Maximum Fluid Temperature||50 (122)||°C (°F)|
|Air Inlet||M 1/4" NPS|
|Fluid Inlet||M 3/8" NPS|
|Polished Forged Aluminum Body||♦|
|Wetted Parts, Stainless Steel||♦|
|Weight||530 (18.7)||g (oz)|
|PH||5 - 8|
|Designation||Max Fluid viscosity (CA 4)||Projector||Nozzle size||Air Consumption||Fluid Output||Fan width at 20cm (8in)||Part number|
|M22 P BASIK||-||-||-||-||-||-||135147200|
|M22 P BASIK||< 20 s||09 BA 3||0.9 mm (0.035 in)||30 m3/h (17.6 cfm)||250 cc/mn (8.5 oz/mn)||31 cm (12.2 in)||135147205|
|M22 P BASIK||20 - 40 s||12 BA 3||1.2 mm (0.047 in)||31 m3/h (18.2 cfm)||270 cc/mn (9.1 oz/mn)||32 cm (12.6 in)||135147206|
|M22 P BASIK||20 - 40 s||15 BA 3||1.5 mm (0.059 in)||32 m3/h (18.8 cfm)||350 cc/mn (11.8 oz/mn)||36 cm (14.2 in)||135147207|
|M22 P BASIK||20 - 40 s||18 BA 3||1.8 mm (0.071 in)||32 m3/h (18.8 cfm)||400 cc/mn (13.5 oz/mn)||39 cm (15.4 in)||135147208|
|Designation||Max Fluid viscosity (CA 4)||Aircap||Nozzle size||Needle||Compatibility||Air Consumption||Fluid Output||Fan width at 20cm (8in)||Part number|
|PROJECTOR||< 20 s||BA 3||0.9 mm (0.035 in)||07 - 12||-||30 m3/h (17.6 cfm)||250 cc/mn (8.5 oz/mn)||31 cm (12.2 in)||1||031147005|
|PROJECTOR||20 - 40 s||BA 3||1.2 mm (0.047 in)||07 - 12||-||31 m3/h (18.2 cfm)||270 cc/mn (9.1 oz/mn)||32 cm (12.6 in)||2||031147006|
|PROJECTOR||20 - 40 s||BA 3||1.5 mm (0.059 in)||14 - 18||-||32 m3/h (18.8 cfm)||350 cc/mn (11.8 oz/mn)||36 cm (14.2 in)||3||031147007|
|PROJECTOR||20 - 40 s||BA 3||1.8 mm (0.071 in)||14 - 18||-||32 m3/h (18.8 cfm)||400 cc/mn (13.5 oz/mn)||39 cm (15.4 in)||4||031147008|
|NEEDLE||-||-||-||07 - 12||nozzle 0.7 to 1.2||-||-||-||6||033140100|
|NEEDLE||-||-||-||14 - 18||nozzle 1.5 to 1.8||-||-||-||7||033140200|
|NOZZLE||< 20 s||-||0.9 mm (0.035 in)||-||aircap BA 3||-||-||-||8||134130200|
|NOZZLE||20 - 40 s||-||1.2 mm (0.047 in)||-||aircap BA 3||-||-||-||9||134130300|
|NOZZLE||20 - 40 s||-||1.5 mm (0.059 in)||-||aircap BA 3||-||-||-||90||134130600|
|NOZZLE||20 - 40 s||-||1.8 mm (0.071 in)||-||aircap BA 3||-||-||-||91||134130700|
|PACK OF SEALS FOR M22G AND M22P||Pack of seals||1||129130901|
|SERVICING KIT FOR M22P||Maintenance pack (includes a pack of seals + gun components)||2||129140902|
Epoxy primer/sealer is a non-porous finish that is typically recommended as the first base coat over bare steel.
Epoxy primer/sealer multi-component is a non-porous finish base mixed with a hardener that is typically recommended as the first base coat over bare steel.
Designed to hide profile & surface imperfections, multi-component polyurethane primers & sealers improve adhesion of top coats to the substrate due to the addition of a hardener.
Designed to hide profile & surface imperfections, water-based primers & sealers are environmentally friendly.
Designed to hide profile & surface imperfections, polyurethane primers & sealers promote adhesion of top coats to the substrate.
Water-Based Wood Stains have all the advantages of oil-based stains. They spread easily, can be repaired, blend effortlessly & have plenty of open time. The thicker formula allows for controlled penetration, which will reduce blotching on softer woods such as Aspen, Pine & Maple.
A wood stain consists of a colorant suspended or dissolved in an agent or solvent. Colored, or ''stained", finishes do not penetrate the pores of the wood to any significant degree.
Chemical Agent Resistant Coating (CARC) can be two-component polyurethane paint commonly applied to military vehicles to provide protection against chemical & biological weapons.
UV-resistant epoxy systems mixed with hardener cure faster & in moist conditions.
UV curable epoxy systems do not require the addition of curing agents. They cure within minutes, or even seconds, and have unlimited working times.
Polyurethane Top Coat is a two- or three-pack isocyanate-cured polyurethane that gives a durable, high gloss finish. Isocyanates included in the hardener are moisture-sensitive & need a specific process for insulating the circuit.
Top Coat Epoxys are used for decorative flooring applications, such as Terrazzo flooring, chip flooring & colored aggregate flooring.
Two-part epoxy coatings were developed for heavy duty service on metal substrates & use less energy than heat-cured.
Water-based polyurethane is popular because of its low odor & low toxicity. It goes on clear without adding a faint color like oil-based versions do & it dries much faster.
The newest metallic epoxy system on the market allows contractors to heighten the effects & make floors look three-dimensional.
Polyurethane water-based coatings offer a very high chemical/physical resistance & steel effect & are environmentally friendly.
A two-component 100%-solid epoxy blended with metallic pigments, Metal Fusion is self-leveling, allowing easy application & seamless floor surfaces.
Polyurethane coatings are particularly recommended for application to surfaces subject to high levels of wear & tear where excellent chemical/physical resistance is required. The metallic parts will give a steel effect.